| .. | ||
| ESP8266_WIFI_Schematic.pdf | ||
| ReadMe.md | ||
Documenting adventures with the GPIO...
Official GPIO layout created by Aleksandr Kutuzov. Official documentation is here!
Connect an external CC1101 to your Flipper
Check out this excellent guide from quen0n on the hardware and configurations needed to increase your SubGHz range!
Sentry Safe plugin pinout
Plugin by H4ckd4ddy
(Flipper) 8/GND -> Black wire (Safe)
(Flipper) 15/C1 -> Green wire (Safe)
NRF24L01+ / Mousejack pinout - 8-pin
Plugin by mothball187 | Affected devices from Bastille research
More info from RogueMaster and Unleashed. (Both include the plugin in their firmware releases.)
2/A7 on FZ goes to MOSI/6 on NRF24
3/A6 on FZ goes to MISO/7 on NRF24
4/A4 on FZ goes to CSN/4 on NRF24
5/B3 on FZ goes to SCK/5 on NRF24
6/B2 on FZ goes to CE/3 on NRF24
8/GND on FZ goes to GND/1 on NRF24
9/3V3 on FZ goes to VCC/2 on NRF24
IRQ/8 is left disconnected on NRF24
If the nRF model is acting a bit flakey, try adding a capacitor to the vcc/gnd lines! I've not tried the Plus model so it may have a bigger need for a cap. Otherwise, I haven't had any major issues. Anything from a 3.3 uF to 10 uF should do. (Watch your positive/negative placement! Negative to ground.) I learned if you wanna get fancy, include a 0.1 uF cap in parallel. The 3.3 uF to 10 uF will respond to slow freq changes while the 0.1 uF will respond to the high freq switching spikes that the larger one cannot. That said, a single 10 uF will likely suffice for the Mousejack attack. ¯\_(ツ)_/¯
NRF24L01+ (B) - 10-pin
Thank you to Amec0e for the information on the newer NRF24L01 (B)!
NRF24: 1 (CE) to FZ 6 (B2)
NRF24: 2 (SCK) to FZ 5 (B3)
NRF24: 3 (CSN) to FZ 4 (A4)
NRF24: 4 (MOSI) to FZ 2 (A7)
NRF24: 6 (MISO) to FZ 3 (A6)
NRF24: 7 or 8 (GND) to FZ GND (8 or 11 or 18)
NRF24: 9 or 10 (VCC) to FZ 9 (3v3)
ESP32-WROOM
NOTE: Use old_hardware.bin if flashing Marauder onto the ESP32-WROOM (thanks wyldgoat!)
Easy Flasher (Windows / Linux / Mac) available here.
ESP32 / ESP32-WROOM Pinout to Flipper Zero
(Thanks E_Surge and wyldgoat for guidance!)
NOTE: Make sure you're using at least an ESP32 v2 or above for full functionality! Good read.
Running an ESP32 single-core and want Marauder? You've gotta head over to V0lk3n's write-up!
ESP32: 3 (RX0) -> FZ: 13 or 15 (these are TX pins)
ESP32: 1 (TX0) -> FZ: 14 or 16 (these are RX pins)
ESP32: GND -> FZ: 8 or 11 or 18 (GND)
ESP32: 5V -> FZ: 1 (5V) OR ESP32: 3.3V -> FZ: 9 (3.3V)
NOTE: Make sure to enable 5v under GPIO on the Flipper
Switch between UART Pins 13/14 and 15/16 setting in FlipperZero
(GPIO -> USB-UART Bridge -> LEFT -> UART Pins)
ESP8266
If you have the ESP8266 and are looking to use a wifi deauth, check out speexvocon's easy web flasher!
If you're looking to give another deauther a try, check out HEX0DAYS repo over here.
ESP8266 Pinout to Flipper Zero
(Thanks PixelHerstel for additional guidance!)
ESP8266: 1 (TX0) -> FZ: 14 or 16 (these are RX pins)
ESP8266: 3 (RX0) -> FZ: 13 or 15 (these are TX pins)
ESP8266: 5 -> FZ: 7
ESP8266: 6 -> FZ: 6
ESP8266: 7 -> FZ: 5
ESP8266: 8 -> FZ: 4
ESP8266: VIN -> FZ: 1
ESP8266: GND -> FZ: 8 or 11 (GND)
FZ: 16 -> FZ: 18 (yes, FZ to FZ)
ESP8266: 5V -> FZ: 1 (5V)
NOTE: Make sure to enable 5V under GPIO on the Flipper
OR ESP32: 3.3V -> FZ: 9 (3.3V) though this can have issues...
Switch between UART Pins 13/14 and 15/16 setting in FlipperZero
(GPIO -> USB-UART Bridge -> LEFT -> UART Pins)
A visual pinout can be seen in this PDF, too.
ESP32-S2 WROVER
ESP32-S2 WROVER Pinout (thanks max_fpv_austria!)
ESP32: 44 (RX0) -> FZ: 13 or 15 (these are TX pins)
ESP32: 43 (TX0) -> FZ: 14 or 16 (these are RX pins)
ESP32: GND -> FZ: 8 or 11 or 18 (GND)
ESP32: 3.3V -> FZ: 9 (3.3V)
Switch between UART Pins 13/14 and 15/16 setting in FlipperZero
(GPIO -> USB-UART Bridge -> LEFT -> UART Pins)
Picture includes wiring pinout for the SD card mod too!
ESP32-CAM (Camera) - FAP FILE HERE!
ESP32-CAM Pinout to Flipper Zero
CAM32: 1 (RX0) -> FZ: 13 or 15 (these are TX pins)
CAM32: 2 (TX0) -> FZ: 14 or 16 (these are RX pins)
CAM32: 3 (GND) -> FZ: 8 or 11 or 18 (GND)
CAM32: 4 (3.3V) -> FZ: 9 (3.3V) OR ESP32: 5V -> FZ: 1 (5V)
LoRa ESP32 Wifi (Wifi + Bluetooth + LoRa 433 MHz)
LoRa ESP32 Wifi Pinout to Flipper Zero
LoRa32: 1 (RX0) -> FZ: 13 or 15 (these are TX pins)
LoRa32: 2 (TX0) -> FZ: 14 or 16 (these are RX pins)
LoRa32: 3 (GND) -> FZ: 8 or 11 or 18 (GND)
LoRa32: 4 (3.3V) -> FZ: 9 (3.3V)
Switch between UART Pins 13/14 and 15/16 setting in FlipperZero
GPIO -> USB-UART Bridge -> LEFT -> UART Pins
Raspberry Pi Zero UART
Raspberry Pi Zero : Prerequisite
Mount your SD Card to your computer and add the following line at the end of /boot/config.txt file.
enable_uart=1
Additionally you can look at the baudrate in the /boot/cmdline.txt file, which should be 115200 by default.
Raspberry Pi Zero : Pinout to Flipper Zero
PiZero: 4 (5V) -> FZ: 1 (5V)
PiZero: 6 (GND) -> FZ: 11 (GND)
PiZero: 8 (UART0_TXD) -> FZ: 14 (RX)
PiZero: 10 (UART0_RXD) -> FZ: 13 (TX)
HC-SR04 Ultrasonic Distance Sensor
Plugin by Sanqui: https://github.com/Sanqui/flipperzero-firmware/blob/hc_sr04/applications/hc_sr04/hc_sr04.c
HC-SR04: 1 (RX0) -> FZ: 13 or 15 (these are TX pins)
HC-SR04: 2 (TX0) -> FZ: 14 or 16 (these are RX pins)
HC-SR04: 3 (GND) -> FZ: 8 or 11 or 18 (GND)
HC-SR04: 4 (5V) -> FZ: 1 (5V)
Switch between UART Pins 13/14 and 15/16 setting in:
Flipper -> GPIO -> USB-UART Bridge -> LEFT -> UART Pins
NMEA 0183 GPS
https://github.com/ezod/flipperzero-gps
GPIO pins 9 (3.3V), 11 (GND), 13 (TX), and 14 (RX)
i2c Tools (by NaejEL)
C0 -> SCL / C1 -> SDA / GND -> GND | 3v3 logic levels only!
https://github.com/NaejEL/flipperzero-i2ctools
HTU21D / SI7021 Temperature Sensor
GPIO pins 9 (3.3V), 11 (GND), 15 (sda), and 16 (scl)
https://github.com/Mywk/FlipperTemperatureSensor
AM2320/AM2321 Temp. Sensor
GPIO pins 9 (3.3V), 11 (GND), 15 (sda), and 16 (scl)
https://github.com/xMasterX/AM2320_Flipper_Plugin
DHT11/22 Temp. Sensor
VCC (none, +, VCC, red wire) 1 (5V) or 9 (3V3)
GND (-, GND, black wire) 8, 18 (GND)
DATA (OUT, S, yellow wire) 2-7, 10, 12-17 (to choose from)
https://github.com/quen0n/FipperZero-DHT-Monitor
UHF RFID YRM100 (FAP / App here)
YRM100: 1 (VCC) -> FZ: 1 (5V)
YRM100: 2 (RXD) -> FZ: 13 or 15 (these are TX pins)
YRM100: 3 (TXD) -> FZ: 14 or 16 (these are RX pins)
YRM100: 4 (EN) -> FZ: 9 (3.3V)
YRM100: 5 (GND) -> FZ: 8 or 11 or 18 (GND)
Switch between UART Pins 13/14 and 15/16 setting in:
Flipper -> GPIO -> USB-UART Bridge -> LEFT -> UART Pins
Also make sure to enable 5V in Flipper -> GPIO
Credit: RekordNadoev / Issue 515
ServoTester (Info/App)
VCC (none, +, VCC, red wire) -> Flipper 1 (5V)
GND (-, GND, black/brown wire) -> Flipper 8 OR 18 (GND)
DATA (OUT, S, yellow wire) -> Flipper 2
Make sure to enable 5V in Flipper -> GPIO
Credit: RekordNadoev / Issue 515
Custom PCB's
Here's some repo's with designs for custom PCB's you can order or build using a prototype board.
DrB0rk
AWOK
Speexvocon (ESP Expansion and Header Extender)
ushastoe
TheOtherLonestar
Oleksii Kutuzov
Donation Information
Nothing is ever expected for the hoarding of digital files, creations I have made, or the people I may have helped.
Ordering from Lab401? USE THIS LINK FOR 5% OFF! (Or code UberGuidoZ at checkout.)
I've had so many asking for me to add this.
BTC: 3AWgaL3FxquakP15ZVDxr8q8xVTc5Q75dS
BCH: 17nWCvf2YPMZ3F3H1seX8T149Z9E3BMKXk
ETH: 0x0f0003fCB0bD9355Ad7B124c30b9F3D860D5E191
LTC: M8Ujk52U27bkm1ksiWUyteL8b3rRQVMke2
PayPal: uberguidoz@gmail.com
So, here it is. All donations of any size are humbly appreciated.
Donations will be used for hardware (and maybe caffeine) to further testing!
