2022-08-03 09:13:27 +00:00
# Documenting adventures with the GPIO...
2022-07-14 23:40:33 +00:00
Official [GPIO layout ](https://miro.com/app/board/uXjVO_LaYYI=/ ) created by [Aleksandr Kutuzov ](https://discord.com/channels/740930220399525928/765282833744265246/993107060172542012 ).
2022-07-09 05:58:38 +00:00
2022-08-04 16:45:24 +00:00
# Sentry Safe plugin pinout
Plugin by [H4ckd4ddy ](https://github.com/H4ckd4ddy/flipperzero-sentry-safe-plugin )
2022-07-09 05:58:38 +00:00
(Flipper) 8/GND -> Black wire (Safe)< br >
(Flipper) 15/C1 -> Green wire (Safe)
2022-08-12 00:19:21 +00:00
# NRF24L01+ / Mousejack pinout - 8-pin
2022-07-09 05:58:38 +00:00
2022-08-13 03:22:29 +00:00
Plugin by [mothball187 ](https://github.com/mothball187/flipperzero-nrf24 ) | Affected devices from [Bastille research ](https://www.bastille.net/research/vulnerabilities/mousejack/affected-devices )
2022-08-04 16:45:24 +00:00
More info from [RogueMaster ](https://github.com/RogueMaster/flipperzero-firmware-wPlugins/tree/unleashed/applications/mousejacker ) and [Unleashed ](https://github.com/Eng1n33r/flipperzero-firmware/blob/dev/documentation/NRF24.md ). (Both include the plugin in their firmware releases.)
2022-07-11 23:04:34 +00:00
2022-08-12 00:19:21 +00:00
2/A7 on FZ goes to MOSI/6 on NRF24< br >
3/A6 on FZ goes to MISO/7 on NRF24< br >
4/A4 on FZ goes to CSN/4 on NRF24< br >
5/B3 on FZ goes to SCK/5 on NRF24< br >
6/B2 on FZ goes to CE/3 on NRF24< br >
8/GND on FZ goes to GND/1 on NRF24< br >
9/3V3 on FZ goes to VCC/2 on NRF24< br >
IRQ/8 is left disconnected on NRF24
2022-07-11 00:56:49 +00:00
2022-07-11 00:57:41 +00:00
2022-07-11 23:04:34 +00:00
If the nRF model is acting a bit flakey, try adding a capacitor to the vcc/gnd lines! I've not tried the Plus model so it may have a bigger need for a cap. Otherwise, I haven't had any major issues. Anything from a 3.3 uF to 10 uF should do. (Watch your positive/negative placement! Negative to ground.) I learned if you wanna get fancy, include a 0.1 uF cap in parallel. The 3.3 uF to 10 uF will respond to slow freq changes while the 0.1 uF will respond to the high freq switching spikes that the larger one cannot. That said, a single 10 uF will likely suffice for the Mousejack attack. ¯\\\_(ツ)_/¯
2022-07-09 05:58:38 +00:00
2022-07-11 00:57:41 +00:00
2022-07-11 22:54:27 +00:00
2022-07-14 23:42:52 +00:00
2022-08-12 00:19:21 +00:00
# NRF24L01+ (B) - 10-pin
Thank you to [Amec0e ](https://github.com/amec0e ) for the information on the newer NRF24L01 (B)!
NRF24: 1 (CE) to FZ 6 (B2)< br >
NRF24: 2 (SCK) to FZ 5 (B3)< br >
NRF24: 3 (CSN) to FZ 4 (A4)< br >
NRF24: 4 (MOSI) to FZ 2 (A7)< br >
NRF24: 6 (MISO) to FZ 3 (A6)< br >
NRF24: 7 or 8 (GND) to FZ GND (8 or 11 or 18)< br >
NRF24: 9 or 10 (VCC) to FZ 9 (3v3)
2022-08-02 04:24:34 +00:00
# ESP32-WROOM
2022-07-14 23:42:52 +00:00
2022-08-02 04:24:34 +00:00
2022-07-17 05:19:32 +00:00
2022-08-02 04:24:34 +00:00
NOTE: Use `old_hardware.bin` if flashing Marauder onto the ESP32-WROOM (thanks wyldgoat!)
2022-08-03 07:43:22 +00:00
< br >
2022-08-02 04:24:34 +00:00
# ESP8266
## ESP32 / ESP32-WROOM / ESP8266 Pinout to Flipper Zero
(Thanks [E_Surge ](https://github.com/ESurge ) and wyldgoat for guidance!)
2022-07-17 05:19:32 +00:00
ESP32: 3 (RX0) -> FZ: 13 or 15 (these are TX pins)< br >
ESP32: 1 (TX0) -> FZ: 14 or 16 (these are RX pins)< br >
ESP32: GND -> FZ: 8 or 11 or 18 (GND)< br >
ESP32: 3.3V -> FZ: 9 (3.3V) ** *OR*** ESP32: 5V -> FZ: 1 (5V)
Switch between UART Pins 13/14 and 15/16 setting in FlipperZero< br >
`(GPIO -> USB-UART Bridge -> LEFT -> UART Pins)`
2022-08-03 09:03:33 +00:00
2022-08-03 09:12:35 +00:00
# ESP32-CAM (Camera)
## ESP32-CAM Pinout to Flipper Zero
CAM32: 1 (RX0) -> FZ: 13 or 15 (these are TX pins)< br >
CAM32: 2 (TX0) -> FZ: 14 or 16 (these are RX pins)< br >
CAM32: 3 (GND) -> FZ: 8 or 11 or 18 (GND)< br >
CAM32: 4 (3.3V) -> FZ: 9 (3.3V) ** *OR*** ESP32: 5V -> FZ: 1 (5V)
2022-08-03 09:03:33 +00:00
# LoRa ESP32 Wifi (Wifi + Bluetooth + LoRa 433 MHz)
## LoRa ESP32 Wifi Pinout to Flipper Zero (PENDING VERIFICATION)
LoRa32: 1 (RX0) -> FZ: 13 or 15 (these are TX pins)< br >
LoRa32: 2 (TX0) -> FZ: 14 or 16 (these are RX pins)< br >
LoRa32: 3 (GND) -> FZ: 8 or 11 or 18 (GND)< br >
LoRa32: 4 (3.3V) -> FZ: 9 (3.3V)
Switch between UART Pins 13/14 and 15/16 setting in FlipperZero< br >
`GPIO -> USB-UART Bridge -> LEFT -> UART Pins`
2022-08-04 06:38:44 +00:00
2022-08-07 12:00:00 +00:00
# Raspberry Pi Zero UART
## Raspberry Pi Zero : Prerequisite
2022-08-07 22:48:53 +00:00
Mount your SD Card to your computer and add the following line at the end of `/boot/config.txt` file.
2022-08-07 12:00:00 +00:00
2022-08-07 22:48:53 +00:00
`enable_uart=1`
2022-08-07 12:00:00 +00:00
2022-08-07 22:48:53 +00:00
Additionally you can look at the baudrate in the `/boot/cmdline.txt` file, which should be `115200` by default.
2022-08-07 12:00:00 +00:00
## Raspberry Pi Zero : Pinout to Flipper Zero
```
PiZero: 4 (5V) -> FZ: 1 (5V)
PiZero: 6 (GND) -> FZ: 11 (GND)
PiZero: 8 (UART0_TXD) -> FZ: 14 (RX)
PiZero: 10 (UART0_RXD) -> FZ: 13 (TX)
```
2022-08-04 06:38:44 +00:00
# Some other accessories to try with Flipper (Code needed!)
## HC-SR04 Ultrasonic Distance Sensor
2022-08-06 11:56:24 +00:00
Plugin by Sanqui: https://github.com/Sanqui/flipperzero-firmware/blob/hc_sr04/applications/hc_sr04/hc_sr04.c
2022-08-04 06:38:44 +00:00
```
HC-SR04: 1 (RX0) -> FZ: 13 or 15 (these are TX pins)
HC-SR04: 2 (TX0) -> FZ: 14 or 16 (these are RX pins)
HC-SR04: 3 (GND) -> FZ: 8 or 11 or 18 (GND)
HC-SR04: 4 (5V) -> FZ: 1 (5V)
Switch between UART Pins 13/14 and 15/16 setting in:
Flipper -> GPIO -> USB-UART Bridge -> LEFT -> UART Pins
```
2022-08-09 06:08:49 +00:00
-----
2022-08-09 04:54:31 +00:00
I've had so many asking for me to add this.< br >
 
**BTC**: `3AWgaL3FxquakP15ZVDxr8q8xVTc5Q75dS` < br >
2022-08-09 06:08:49 +00:00
**BCH**: `17nWCvf2YPMZ3F3H1seX8T149Z9E3BMKXk` < br >
**ETH**: `0x0f0003fCB0bD9355Ad7B124c30b9F3D860D5E191` < br >
**LTC**: `M8Ujk52U27bkm1ksiWUyteL8b3rRQVMke2`
2022-08-09 04:54:31 +00:00
So, here it is. All donations of *any* size are humbly appreciated.< br >
 
2022-08-09 06:08:49 +00:00
Donations will be used for hardware (and maybe caffeine) to further testing!< br >
2022-08-09 04:54:31 +00:00
