# Official info
The Wifi devboard ships with [Blackmagic firmware](https://github.com/flipperdevices/blackmagic-esp32-s2) installed. The Flipper documentation [is here](https://docs.flipperzero.one/development/hardware/wifi-debugger-module), and Blackmagic is [over here](https://black-magic.org/).
Quick start: Connect to the SSID `blackmagic` using the password `iamwitcher` or plug the wifi devboard in via USB.
# ESP32 Wi-Fi Pentest Tool
Check out [Frog's write-up](https://github.com/FroggMaster/ESP32-Wi-Fi-Penetration-Tool) and build for quick and easy flashing! Seriously, it's basically just a double-click.
# Some quick steps to get [Marauder](https://github.com/justcallmekoko/ESP32Marauder) installed
(Direct from the dev WillStunForFood on Discord - check out [his video walkthrough](https://www.youtube.com/watch?v=_YLTpNo5xa0) too!):
- Plug the WiFi dev board directly into your PC
- Upload the MarauderOTA firmware from source via Arduino IDE
- Use the MarauderOTA firmware to flash the Marauder Flipper bin over WiFi
The first step in the wiki documentation [starts here](https://github.com/justcallmekoko/ESP32Marauder/wiki/flipper-zerowhile).
(Then you should have the necessary links to the follow on documentation to get the firmware installed.)
ESP32-S2 is the correct board if you are installing on the Flipper WiFi Dev Board.
If you are using the Marauder OTA method, you shouldn't have to install any libraries.
The only other thing you should have to install is the boards for the ESP32 in the Arduino IDE and the drivers for the ESP32-S2.
Commands `channel`, `scanap`, `sniffbeacon`, `sniffdeauth`, `sniffpmkid`, `stopscan`, `clearap`
------------------------------------------------------------------------------
Example Attack Profile ([from Discord](https://discord.com/channels/740930220399525928/967843558520418384/997185157175988264)):
Use command `scanap` stop with `stopscan` when done.
List all found Beacons from previous steps via `list -a`
Note the enumeration of your target Beacon...
Use `select -a x` command to select your target. (x being your target # from previous step)
Execute chosen attack `attack -t deauth`
Use `stopscan` when done.
-----------------------------------------------------------------------------------
Connecting to the devboard with a Mac ([from Discord](https://discord.com/channels/740930220399525928/967843558520418384/998043936977330276))
Open Terminal
Enter ls /dev/tty.*
You will be provided with several USB directories. Select one that has your flippers name in it example: /dev/tty.usbmodemflip_XXXXX3
Add "screen" in the prefix and the baud rate as the suffix to the command after copy pasting.....
screen /dev/tty.usbmodemflip_XXXXX3 115200
Hit reset on the flipper board and you'll see it populate. If it doesn't, simply try the other flipper directory name.
-----------------------------------------------------------------------------------
# Quick steps from Rabid Root...
# AND a great step by step from E_Surge!
Also from E_Surge: "Flashed esp32marauder directly to the esp32-s2 using the esptool command -- wasn't working until a PC restart and boom. But it took about three hours of different methods, attempts, and finally restarting of devices etc."
`esptool -p PORT -b 460800 --before default_reset --after hard_reset --chip esp32s2 write_flash --flash_mode dio --flash_freq 80m --flash_size 4MB 0x10000 esp32_marauder_v0_9_9_20220628_flipper.bin`
# If serial connection looks scrambled... (thanks Frog!)
Frog also noted that it's wise to reflash the Flipper firmware if such issues are persisting.
Start with the Official firmware, test, then move to a unlocked one if desired.